INSTRUCTIONS
Note: When using ADAMENT 50 WG Fungicide in tank mixtures, all products in water-soluble packaging should be added to the tank before any other tank mix partner, including ADAMENT 50 WG Fungicide. Allow the water-soluble packaging to completely dissolve and the product(s) to completely disperse before adding any other tank-mix partner to the tank. If using ADAMENT 50 WG Fungicide in a tank mixture, observe all directions for use, crop/sites, use rates, dilution ratios, precautions, and limitations which appear on the tank mix partner product label. No label dosage rate may be exceeded, and the most restrictive label precautions and limitations must be followed. This product must not be mixed with any product which prohibits such mixing. Tank mixtures or other applications of products referenced on this label are permitted only in those states in which the referenced products are registered.

REENTRY PPE
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: - Coveralls - Chemical-resistant gloves made of any waterproof material - Shoes plus socks

PPE
Personal Protective Equipment (PPE) Applicators and other handlers must wear: - Long-sleeved shirt and long pants - Shoes plus socks - Chemical resistant gloves made of any waterproof material

TANK MIX
MIXING PROCEDURES Prepare no more spray mixture than is needed for the immediate operation. Thoroughly clean spray equipment before using this product. Vigorous agitation is necessary for proper dispersal of the product. Maintain maximum agitation throughout the spraying operation. Do not let the spray mixture stand overnight in the spray tank. Flush the spray equipment thoroughly following each use and apply the rinsate to a previously treated area. ADAMENT 50 WG Fungicide Alone: Add approximately 1/2 of the required amount of water to the mix tank. With the agitator running, add the ADAMENT 50 WG Fungicide to the tank. Continue agitation while adding the remainder of the water. Begin application of the solution after the ADAMENT 50 WG Fungicide has completely and uniformly dispersed into the mix water. Maintain agitation until all of the mixture has been applied. ADAMENT 50 WG Fungicide + Tank Mix Partners: Add approximately 1/2 of the required amount of water to the mix tank. Start the agitator running before adding any tank mix partners. In general, tank mix partners should be added in this order: products packaged in watersoluble packaging*, wettable powders, wettable granules (dry flowables), liquid flowables such as ADAMENT 50 WG Fungicide, liquids, and emulsifiable concentrates. Always allow each tank mix partner to become fully and uniformly dispersed before adding the next product. Provide sufficient agitation while adding the remainder of the water. Maintain agitation until all of the mixture has been applied.

INSTRUCTIONS
Note: When using ADAMENT 50 WG Fungicide in tank mixtures, all products in water-soluble packaging should be added to the tank before any other tank mix partner, including ADAMENT 50 WG Fungicide. Allow the water-soluble packaging to completely dissolve and the product(s) to completely disperse before adding any other tank-mix partner to the tank. If using ADAMENT 50 WG Fungicide in a tank mixture, observe all directions for use, crop/sites, use rates, dilution ratios, precautions, and limitations which appear on the tank mix partner product label. No label dosage rate may be exceeded, and the most restrictive label precautions and limitations must be followed. This product must not be mixed with any product which prohibits such mixing. Tank mixtures or other applications of products referenced on this label are permitted only in those states in which the referenced products are registered.

REENTRY PPE
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: - Coveralls - Chemical-resistant gloves made of any waterproof material - Shoes plus socks

PPE
Personal Protective Equipment (PPE) Applicators and other handlers must wear: - Long-sleeved shirt and long pants - Shoes plus socks - Chemical resistant gloves made of any waterproof material

TANK MIX
MIXING PROCEDURES Prepare no more spray mixture than is needed for the immediate operation. Thoroughly clean spray equipment before using this product. Vigorous agitation is necessary for proper dispersal of the product. Maintain maximum agitation throughout the spraying operation. Do not let the spray mixture stand overnight in the spray tank. Flush the spray equipment thoroughly following each use and apply the rinsate to a previously treated area. ADAMENT 50 WG Fungicide Alone: Add approximately 1/2 of the required amount of water to the mix tank. With the agitator running, add the ADAMENT 50 WG Fungicide to the tank. Continue agitation while adding the remainder of the water. Begin application of the solution after the ADAMENT 50 WG Fungicide has completely and uniformly dispersed into the mix water. Maintain agitation until all of the mixture has been applied. ADAMENT 50 WG Fungicide + Tank Mix Partners: Add approximately 1/2 of the required amount of water to the mix tank. Start the agitator running before adding any tank mix partners. In general, tank mix partners should be added in this order: products packaged in watersoluble packaging*, wettable powders, wettable granules (dry flowables), liquid flowables such as ADAMENT 50 WG Fungicide, liquids, and emulsifiable concentrates. Always allow each tank mix partner to become fully and uniformly dispersed before adding the next product. Provide sufficient agitation while adding the remainder of the water. Maintain agitation until all of the mixture has been applied.